Peak Pro Control runs a Puffco Peak Pro from a browser tab over
Bluetooth, with no app to install and no account. This page covers what you need, how to
connect the first time, what each part of the app does, and what to do when a connection
fails. For heat settings by dab style, see the dab temperature guide.
Before you start
Chrome or Edge. On a computer, or Chrome on an Android phone. iPhone,
iPad, Safari and Firefox don't support Web Bluetooth, so the page can't connect from them.
It has been tested with Chrome on Windows 11; other systems should work but haven't been
tried yet.
A Peak Pro on current firmware. Firmware older than AB
uses a different Bluetooth layout, and the app tells you if it finds one. Update it with
the Puffco app first.
One connection at a time. The Peak Pro talks to one thing at once.
Close the Puffco app on your phone, or turn off the phone's Bluetooth, before you
connect.
Close by. It works within Bluetooth range of the device. It isn't remote
control over the internet.
A paired computer. The Peak Pro only answers over an encrypted link, so
your computer has to pair with it once. The next section covers that.
Connect for the first time
Close the Puffco app on your phone.
Put the Peak Pro in pairing mode: hold the button until the logo glows
blue. It turns off and back on before the blue light appears.
Open the app, press Connect, pick the Peak Pro in
Chrome's list, and press Pair.
The line under the device name shows each step: Connecting, Pairing, Unlocking. While it
says Pairing (… s left), accept any prompt from Chrome or Windows. It waits up to
30 seconds.
When it says Connected, the ring shows the live temperature and the tabs
appear below it.
After the first time, Connect works without pairing mode. Pairing a computer may mean the
Puffco app on your phone has to pair again the next time you use it.
Pairing on Windows
Windows Settings may not list the Peak Pro at all. If the app says this computer isn't
paired, the pairing didn't happen at the system level. In testing, what worked was
Windows' confirm-only custom pairing; the
README's pairing section
has the details. If Windows keeps saying a pairing is already in progress, restart the
computer and try again.
The app, part by part
The ring
The big number is the heater's live temperature. Under it, the device's state:
Idle, Heating to 545°F, Ready, Cooling down or
Asleep. During a heat cycle the ring fills as each stage runs, and it glows in
the light color of the profile in use.
Heating
Pick one of the four profiles under Heat profile, then press
Heat with and the profile's name. While it heats:
Stop ends the heat cycle.
+10°F (or +5°C) raises the target, and +10 s adds
time.
Target, Preheat or Time left, Battery and Chamber show below.
The profile buttons are locked until the heat cycle ends.
Profiles tab
Edit each of the four profiles and press Save to write it to the
device. The device's limits apply:
Name: up to 31 characters.
Temperature: 400–644°F (204–340°C).
Duration: 15–120 seconds.
Boost: adds 1–36°F (1–20°C) for 1–60 seconds.
Light color: if a profile uses one of the device's animated lights, the field says
so.
Copy to My profiles keeps a copy on the Library tab.
Library tab
Templates: 12 ready-made profiles and 4 sets of four, with
temperatures from the Cape Cod Cannabis and Leafly dabbing guides. Star one to add it
to Favorites.
Build your own set of four: pick a lowest and highest temperature and
it spreads four profiles between them.
My profiles: profiles saved in this browser, with
Back up and Restore.
Loading puts a profile into one of the four slots. The profile it replaces is kept in
My profiles, unless it matches a template. Loading is off while the device heats.
Device tab
Device name: up to 29 characters.
Light brightness: 15–100%.
Stealth mode: dims the lights while heating.
Ready mode: picks which profile the device's ready mode uses, or
turns it off.
Mood light: turns the light on in any color for two hours, or off.
Turn off device: asks first. Press the device's button to wake it
again.
A setting this firmware doesn't have is greyed out.
Stats tab
Total dabs, dabs per day, dabs left on this charge, a trip counter, total heating time,
battery and charging details, the chamber, and device details such as the firmware
build. Refresh reads them again.
Protocol log tab
Every Bluetooth exchange with the device. Show polling reads adds the
regular status reads. Copy log copies it for a bug report.
°F and °C
The switch at the top right changes every temperature in the app, including the
profile editor and the templates. The browser remembers your choice.
When it won't connect
When a connection fails, the app shows what went wrong and what to try. Here are the same
messages with a little more detail.
The Peak Pro isn't in Chrome's list
Wake the device with its button. Asleep, it doesn't show up.
Close the Puffco app on your phone. While the phone is connected, the device
doesn't show up anywhere else.
Move closer, and check that Bluetooth is on for the computer.
Connecting to this computer for the first time? Put it in pairing mode (hold the
button until the logo glows blue) and press Connect again.
The app says:The Peak Pro refused the connection
A device that hasn't paired with this computer only accepts a new connection while it
is in pairing mode.
Close the Puffco app on your phone, or turn off Bluetooth on the phone.
Hold the device button until the logo glows blue.
Press Connect and pick the device again while it is glowing blue.
If Windows asks to pair the device, allow it.
Still failing? Remove the Peak Pro under Windows Settings > Bluetooth &
devices, then try again.
The app says:This computer isn't paired with the Peak Pro, so it won't answer
Chrome connected, but the device ignores everything until the link is encrypted, and
that needs a pairing at the system level.
Close the app's tab and the Puffco app on your phone.
Put the device in pairing mode (hold the button until the logo glows blue).
Pair it with this computer from your system's Bluetooth settings. On Windows, see
Pairing on Windows above.
If Windows reports a pairing already in progress, restart the computer and pair
again.
Once it is paired, come back and press Connect.
The app says:The Peak Pro dropped the connection during setup
Wait a few seconds and press Connect again.
If it keeps dropping, put the device in pairing mode and connect again.
Still stuck? Remove the Peak Pro under Windows Settings > Bluetooth &
devices, then pair again.
The app says:The Peak Pro connected but didn't answer
Remove the Peak Pro under Windows Settings > Bluetooth & devices if it is
listed.
Put the device in pairing mode and press Connect.
Accept any pairing prompt from Chrome or Windows.
Still stuck? Press Copy technical details under the message and
report it.
The app says:This Peak Pro is on older firmware
Firmware older than AB uses a different Bluetooth layout that this app
doesn't support. Update the device with the Puffco app, then connect again.
The app says:This browser can't use Bluetooth
Open the page in Chrome or Edge on a computer, or Chrome on an Android phone. If you're
already in one of those, check that the computer or phone has Bluetooth turned on.
Connected, but a button or setting is greyed out
Loading templates and profiles is off while the device heats. Stop the heat cycle,
or wait for it to end.
A setting the device's firmware doesn't have is greyed out on the Device tab.
Terpenes and temperature
Terpenes carry a concentrate's flavor and smell, and the lighter ones boil off first.
Five of them make up most of what you taste in cannabis:
The big five terpenes, from lowest boiling point to highest
Terpene
Boils at
Aroma
Reported effects
Pinene
311°F (155°C)
Fresh pine, herbs
Alertness, focus, memory
Myrcene
334°F (168°C)
Earthy, musky, ripe mango
Relaxing and sedating
Limonene
349°F (176°C)
Citrus, lemon and orange rind
Uplifting, energizing, stress relief
Linalool
388°F (198°C)
Floral, lavender
Calming, eases anxiety
Caryophyllene
495°F (257°C)
Black pepper, spice, wood
Calming; the one terpene that also binds to CB2 receptors
Four of the five boil below the Peak Pro's lowest setting of 400°F (204°C), so every heat
setting vaporizes them. The cooler the setting, the more of their flavor reaches you before
it scorches. That's why the flavor templates sit at the low end and the cloud-chasing ones
at the top.
Caryophyllene, the peppery one, is a heavier molecule and boils around 495°F (257°C),
inside the Peak Pro's range. Many cannabis charts list it at 266°F (130°C), but that's its
boiling point close to a vacuum, not at normal air pressure
(PubChem).
Terpenes also evaporate slowly at room temperature, so keep concentrates sealed, cool and
out of the light.
Yes. Open the demo (?demo on the address) and press
Connect demo. It runs the real app against a simulated Peak Pro that
heats, cools and saves profiles. Other demo modes act out connection problems:
?demo=unpaired (connection refused), ?demo=notpaired (no
pairing), ?demo=pairing (pairing completes after a few tries) and
?demo=stuck (a read that never answers).
Do I need an account? Where are my profiles kept?
No account. The four profiles and the device settings live on the Peak Pro itself.
My profiles, favorites and your °F/°C choice are saved in this browser only, so they
don't follow you to another computer or browser. Use Back up on the
Library tab before clearing site data or switching computers, and
Restore to bring them back.
Does the site collect anything?
No. There are no analytics, no cookies and no server behind the page: it's static
files on GitHub Pages, and the Bluetooth traffic goes straight from your browser to the
device. Like any website, the host (GitHub) and the font service (Google Fonts) see
the usual request details, such as your IP address.
Can I use it and the Puffco app at the same time?
No. The Peak Pro takes one connection at a time. Close the Puffco app (or turn off
the phone's Bluetooth) before connecting here, and press Disconnect
here before going back to the phone.
What happens if the page disconnects while heating?
The heat cycle runs on the device, so it carries on and ends on its own timer. The
app shows Disconnected; press Connect to pick up again.
Which devices and firmware work?
The Peak Pro, on firmware AB or newer. Everything in the app has been
confirmed on a real Peak Pro (firmware build 5652c02) from Chrome on
Windows 11. Other Puffco devices haven't been tested.
Can I control it from Home Assistant?
Yes, with ha-puffco-peak,
a HACS integration that runs the same device from Home Assistant over Bluetooth,
locally. Only one of them can be connected at a time.
Is it safe?
It uses the same Bluetooth controls as the Puffco app and keeps every value within
the device's limits. Nothing is permanent: no firmware is flashed and nothing is reset,
and you can change any setting back here, on the device or in the Puffco app.
Turning the device off asks first.
It's still a heater. Don't leave it heating unattended.
Found a bug?
Report a problem
(also at the bottom of the app) opens a bug form on GitHub with the app version filled
in. It helps to say whether the demo does the same thing, and
to paste the Copy technical details text from a connection error or
the Copy log text from the Protocol log tab. Posting needs a GitHub
account.
Is this made by Puffco?
No. It's an independent, open-source project (GPL-3.0), not affiliated with Puffco.
The Bluetooth protocol was worked out from my own device; the
source
credits the groundwork. Use it only with a device you own.